Saturday, 19 November 2011

Mounting my Hot End

It's come to my attention that a few people have tried to use a Groove mount for my hot ends.

The White PTFE is not structural !

You MUST use the brown PEEK Block to mount and support my Hot End.
I have included a few mounting examples:

Using Wades geared extruder

This is the Wade Extruder from http://www.thingiverse.com/thing:11892 
Using Adrians extruder
And the mounting on my huxley.


Wednesday, 27 July 2011

Hybrid Huxley is coming along

I got Motors today. Zapp supplied them as they were in stock.


Note the very tidy work bench :)
 The Patented Belt clamps on the X axis
 You may be able to spot a few odd design issues.....


Sunday, 24 July 2011

Thermistor table for my thermistors.

Several people have asked me for this so here goes.


// /usr/local/bin/createTemperatureLookup.py --r0=100000 --t0=25 --r1=0 --r2=4700 --beta=4267 --max-adc=1023
// r0: 100000
// t0: 25
// r1: 0
// r2: 4700
// beta: 4267
// max adc: 1023
#define NUMTEMPS 20
short temptable[NUMTEMPS][2] = {
   {1, 713},
   {54, 236},
   {107, 195},
   {160, 172},
   {213, 157},
   {266, 144},
   {319, 134},
   {372, 125},
   {425, 117},
   {478, 110},
   {531, 103},
   {584, 96},
   {637, 89},
   {690, 83},
   {743, 75},
   {796, 68},
   {849, 59},
   {902, 48},
   {955, 34},
   {1008, 3}
};

Wednesday, 20 July 2011

My Hot-End design and other details.

It's about time I updated and wrote about this.

In the past I write about various Hot-End failures, so I designed my own hot end which still works and I still use from time to time.
That Hot end works well but is VERY Dribbly, resulting in rather untidy prints.

I put together an updated standard Reprap hot-end :
http://www.reprap.org/wiki/Geared_extruder_nozzle
This also failed. The PTFE split where it screws into the Brass Nozzle.

Several design ideas later I found a combination that prints cleanly and is strong enough.


The Nozzle is unchanged from the standard reprap design.






The PTFE has a shoulder turned onto it at 10.5mm dia X 4 mm long.




The PEEK is drilled to 8mm then 10.5mm approx 6mm deep.




The PTFE sits inside the PEEK block supporting it.







 The Heater I make 8 mm thick, rather than 10mm. It's Pictured here with resistor and Thermistor installed.

This has proven a strong and resillient Hot-End.
I have made and sold a good few of these with no complaints.
You will find these hot ends on sale at http://www.emakershop.com




Sunday, 24 October 2010

Heater works very Well.

After getting my machine going, I installed my design of heater.
I built a new connections board for it. - 2 LED's, Resistor and a 4 pin Molex header.
Why 2 LED'S ? - I install em both ways around so 1 is on nomatter which way the heater is connected.

I also had to make a new Z flag as the new heater is longer.

It gets Nozzle temp much quicker than the Block Heaters.
The nozzle is only 2 degrees lower than the heater (According to my IR beam thingy doofah).
The Block heater was 5 degrees C cooler.

It prints well, even after turning up the Extrusion speed.
It stays put, no noticable movement in it.
The M4 screws that keep the PEEK in plase stay Cool.

I really can't see any operational disadvantages here and now, howerver it is not easy to make.

You need a good lathe with a 4 jaw Chuck.
You need to be able to hold and spin a lump of  brass 10mm x 20 mm x 35 mm. 50% Off Center.
You also need to hold the whole thing steady enough and fast enough to get the 0.5 mm hole in the end.

I'll get some pictures up either later tonight or tomorrow.

Heater: Update 2

Spent the morning completing my new Heater.
I glued, with Fire cement, the thermister into a 1 mm hole, about 3mm deep between the heater and Nozzle. That seems to me to be the most logical place for it.

The whole thing is also encased in kapton Tape so it can't ping out.

The PEEK block needed some thought or I'd never do up the nuts on the bottom, or worst still, transfer all the heat up the M4 rods.
The Heater side nut is recessed into the PEEK with enough space to get a socket on to it.
The resistor wires have been crimped and Insulated and I'm prety much ready to go.

Once i get the machine printig later today (I hope) I can swap over to the new design.

If this works I'll get on and do some propper drawings and maybe even make some more and try out the removable nozzle.